Error code
Wolf built-in oven error code E46
Wolf error code E46: the cleaning cycle did not behave as it should — either the cavity did not heat the way the control expects, or it went past where it should have stopped, on a built-in oven, where every part named here sits behind trim that is screwed into the cabinetry rather than behind a panel that slides out. What the code covers, what to check first, and what it does not tell you — on built-in ovens & steam ovens.
- From $95 diagnostic, credited to the repair
- 59 cities and neighborhoods covered
- OEM parts available on order
- In writing the price, before anything is opened
What we can confirm
Code E46, from the manufacturer's own documentation
A code is only meaningful together with the generation showing it — the same two digits mean different things across generations, and that is the commonest reason a code looked up online leads somewhere wrong. This one is recorded on E Series legacy.
The code
E46
The cleaning cycle did not behave as it should — either the cavity did not heat the way the control expects, or it went past where it should have stopped, on a built-in oven, where every part named here sits behind trim that is screwed into the cabinetry rather than behind a panel that slides out
or call (305) 449-9681
What it narrows down to
Elevated cavity temperature in phase 2 of Pyrolysis operation
What you are probably seeing
Diagnostic
From $95, credited to the repair
What it looks like from the kitchen
The symptom this code usually arrives with
A code names the subsystem; the symptom is what sent you to look at the display in the first place. That page says what it usually turns out to be, cheapest cause first.
-
The cycle found it rather than caused it Oven dead after a self-clean cycle
The oven ran its cleaning cycle and has not worked since. It is common, you did nothing wrong by using the feature, and what failed was usually already marginal before the cycle started.
- Worked before the cycle, dead after it
- Door still locked, cavity cold
- A code about cavity temperature or rate of rise
On the same generation
What else belongs to the E Series legacy
A code belongs to a generation rather than to one cabinet. These are the other codes yours can show, and the models that can show this one — a display often has more than one thing to say, and the model number decides what any of it costs to put right.
Other codes this generation can display
RTD Shorted
No Broil Element detected
Lock/Door inputs to the control board are invalid for cleaning
No published cause
DLB2 relay open
RM HIV Fuse Error
Oxidized contacts between relay board and door lock motor
RTD Circuitry error
Touch pad communication error detected by the user interface module
HIV SPI Com Err Detected by HV-Micro
HSWD active, should be inactive
RM Ambient Thermistor open
The same two digits mean different things across generations. Search the full code list
Models that can display this code
The number on the data plate decides which parts exist and how quickly they arrive. All models
In more detail
About Wolf built-in oven error code E46
What this one means
The cleaning cycle did not behave as it should — either the cavity did not heat the way the control expects, or it went past where it should have stopped, on a built-in oven, where every part named here sits behind trim that is screwed into the cabinetry rather than behind a panel that slides out. It is a code the manufacturer publishes for this appliance, not one we have worked out — and it is decoded here rather than left as three characters on a display.
What the code covers
A published cause names a circuit rather than a component, which is the single most useful thing to know before ordering a part. This one covers:
- The door lock and its switches, which the cycle will not start without
- The cavity sensor reading the wrong temperature
- An element or its relay not carrying what was asked of it
- Elevated cavity temperature in phase 2 of Pyrolysis operation
Worth doing before you call
- Note which cavity it is on a double oven — the code says upper or lower and that is half the diagnosis
- Let the oven cool right down, then switch it off at the breaker for thirty seconds
- Take everything out of the cavity, including racks the maker says not to leave in
Then what
Self-clean runs a domestic oven hotter than anything else it ever does, which is why it is where a marginal sensor or a tired relay finally shows itself. The problem is usually real, and it was there before the cycle.
This code is published for built-in ovens & steam ovens. The full list of codes has the rest of them, searchable, including the labels older and newer machines use for the same conditions.
This article is based on:
- Official manufacturer documentation
- Internal repair procedures
- Technician repair history
- Company quality standards