Error code
Wolf dual fuel range error code 10
Wolf error code 10: the appliance lost power in the middle of doing something and stopped where it was, on a dual fuel range, which is two appliances on one chassis: gas burners above, an electric oven below, and one control board answering for both. What the code covers, what to check first, and what it does not tell you — on ranges.
- From $95 diagnostic, credited to the repair
- 59 cities and neighborhoods covered
- OEM parts available on order
- In writing the price, before anything is opened
What we can confirm
Code 10, from the manufacturer's own documentation
A code is only meaningful together with the generation showing it — the same two digits mean different things across generations, and that is the commonest reason a code looked up online leads somewhere wrong. This one is recorded on Dual fuel range legacy.
The code
10
The appliance lost power in the middle of doing something and stopped where it was, on a dual fuel range, which is two appliances on one chassis: gas burners above, an electric oven below, and one control board answering for both
or call (305) 449-9681
What it narrows down to
Power surges or outages may trigger this error
What you are probably seeing
Diagnostic
From $95, credited to the repair
What it looks like from the kitchen
The symptom this code usually arrives with
A code names the subsystem; the symptom is what sent you to look at the display in the first place. That page says what it usually turns out to be, cheapest cause first.
-
Sometimes the house rather than the oven Oven dead after a power cut
The storm passed, everything else came back on, and the oven did not. On this brand the appliance often has a specific opinion about what the electricity did, and it is worth reading before anybody is called.
- Dead since an outage or a surge
- Working, but complaining about voltage
- A neutral or leg condition on the display
On the same generation
What else belongs to the Dual fuel range legacy
A code belongs to a generation rather than to one cabinet. These are the other codes yours can show, and the models that can show this one — a display often has more than one thing to say, and the model number decides what any of it costs to put right.
Other codes this generation can display
Door lock or unlock switches not sensed within 60 seconds
Over temperature occurs when the oven reaches a temperature of 630°F
Open circuit detected on RTD oven sensor
Shorted circuit detected on the RTD sensor
SPI communication lost from ECH to the control board as reported by
EEPROM checksum is incorrect. Checked at power-up
Meat probe detected as shorted
Analog to digital error during calibration phase
Power relay shorted, sensed as closed when should be open
No published cause
Communication lost with the oven controller
Cooling fan apparency switch is reporting cooling fan failure
The same two digits mean different things across generations. Search the full code list
In more detail
About Wolf dual fuel range error code 10
What this one means
The appliance lost power in the middle of doing something and stopped where it was, on a dual fuel range, which is two appliances on one chassis: gas burners above, an electric oven below, and one control board answering for both. It is a code the manufacturer publishes for this appliance, not one we have worked out — and it is decoded here rather than left as three characters on a display.
What the code covers
A published cause names a circuit rather than a component, which is the single most useful thing to know before ordering a part. This one covers:
- A cut, a brownout or a surge during a cook or a clean cycle
- A breaker that tripped and was reset
- A cycle that never finished and was never cleared
- Power surges or outages may trigger this error
What to try yourself
- Check whether the burners still light — gas and electric fail independently here
- Switch the breaker off for thirty seconds and back on
- Start the appliance again and watch whether the code comes back
Then what
A code that appears once after a storm is history. One that returns on a settled supply is not about the power at all, and the next step is measuring rather than resetting.
This code is published for ranges. The full list of codes has the rest of them, searchable, including the labels older and newer machines use for the same conditions.
This article is based on:
- Official manufacturer documentation
- Internal repair procedures
- Technician repair history
- Company quality standards